- Networker pro 8 channel nvr with scweasyconnect install#
- Networker pro 8 channel nvr with scweasyconnect Bluetooth#
Here's a direct link to the "Can I use “x” brand camera or NVR with an SCW camera or NVR?" question.Ī “VCA” Event must be set up first at the NVR. Please see our Third Party Support Policy for more info. Note: Even after this setup certain features such as motion detection, motion recording, time sync, audio, PTZ control etc may not be supported and relies entirely on ONVIF version of the camera and the implementation by the manufacturer. Please contact the camera’s manufacturer for assistance with any of these steps and information required. The port information is gathered - including web port, RTSP port, management and any other ports the camera may use. The third party camera is at least ONVIF 2.0 Profile S compatible and ONVIF compliance mode is turned on (if applicable) The third party camera has been assigned an IP matching your local network The third party camera(s) must be on a separate PoE switch connected to your network/router (ONVIF does not support direct connection) The following checklist is provided - these steps must be completed before an SCW technician can provide support. Third Party Checklist - Steps for Support SCW technicians are also unable to contact other manufacturers for information on the third party camera.
Networker pro 8 channel nvr with scweasyconnect install#
Under no circumstances will SCW install or support third party software to configure third party cameras.
You are responsible for finding an open IP Address on your Network, assigning the IP to the camera, and finding out what protocol and ports it may use, as well as any steps to activate ONVIF on the camera. SCW is unable to support third party cameras beyond showing you where to enter the information to connect the camera. This often requires manufacturer specific software or instructions that SCW technicians are unable to provide and support. This requires your third party camera to be plugged into an external PoE switch, assigning an IP, and configuring ONVIF settings on the camera. Third party cameras make the setup significantly more complicated due to the fact that ONVIF does not support direct connections like “SCWEas圜onnect”. When you combine our cameras and NVRs the process is completely plug and play, no complicated networking required.
Here's a direct link to the "How do I set up Motion Recording?" question.Īt SCW we pride ourselves on having the easiest setup in the industry. This can be done by going to Storage→ Schedule Settings and changing the schedule from continuous to motion. Make sure to hit save before you close the page! You’ll also need to setup the recording schedule. Anything inside the grid will be detected on motion. Click the “Start Drawing” button below the box, and draw a grid on the screen. If there is not a red grid on the video stream, you’ll need to draw one. Vanguard, Executive, Super or Networker Linesįrom a web browser, log into your NVR and go to “Configuration” at the top: Event→ Motion Select your camera from the dropdown menu at the top, and make sure that the “Enable Motion Detection” box is checked. This can be done by going to Camera→ Schedule and changing the schedule from continuous to motion.
Click the “Start Drawing” button on the right, and draw a grid on the screen. Select the camera you’d like to set up from the drop down menu at the top, and make sure that the “Motion” toggle is set to On. What do I do?" question.įrom a web browser, log into your NVR and go to “Setup” at the top Camera→ Motion. Here's a direct link to the "My NVR's mouse doesn’t work. VANGUARD/NETWORKER - Right click anywhere and go to Menu → Configuration→ Live View and change the “Video Output Interface” to your preference. If that works, you’ll need to change the default menu input.ĪDMIRAL - Right click anywhere and go to Menu → System → Preview → Menu Output to change your display preference. If you are currently plugged into the HDMI port on the back of the recorder, please try plugging a cable into the VGA port on the back of the recorder and testing the mouse. Most likely you are plugged into the default “monitor” output and thus can’t see your mouse on the screen.
Networker pro 8 channel nvr with scweasyconnect Bluetooth#
(a bluetooth mouse will not work, but wireless RF will) Every NVR has two default screen outputs: A “menu” output for controlling your cameras/NVR, and a “monitor” output, for purely displaying your cameras. Remember that any mouse that does not require software and should connect. If you NVR's mouse fails, power cycle your NVR, or unplug and reconnect the USB mouse.
0 kommentar(er)
